The safety of handheld fiber laser welding machine-Serena

The safety of handheld fiber laser welding machine-Serena

The safety of handheld fiber laser welding machine.

How is the safety of XT laser handheld welding machine.

1. The welding head is connected to the ground clamp.

Only when the ground clamp clamps the metal, the welding head can emit light.

If it is clamped in non-metal, even if the button is pressed.

It will not emit light, to avoid misoperation if it is not fully prepared.

2. The focal length of the welding head is about 150MM.

So the range beyond 30CM of the welding head is safe.

So please set a safety warning line for the 30CM near the operating table.
3. Welding requires the light to be out of focus.

The welding effect is the best and the safety is the highest.

It can avoid sparks caused by strong light and can also extend the life of the protective lens.

Defocusing is to adjust the scale on the copper nozzle of the welding head.

Where the test time is strongest, the copper nozzle can be adjusted up and down to form defocusing

Sometimes the strong light welding will burn the protective glasses.

And the sparks will cause the operator’s clothes to burn, etc., so it is recommended to test the off-focus before operation.
4. Radiation problem. The certificate shows that the radiation level of the welding machine is level 4, which is in line with the body’s acceptance range, so don’t worry.

5. Basic protective measures must be taken before operation: wear heat-resistant gloves and protective glasses

laser welding machine

Stainless steel welding,handheld fiber laser welder-Jill

Stainless steel brass aluminum welding,handheld fiber laser welder-Jill

handheld fiber laser welder,it is easy to move.

It can welding Stainless steel, middle steel, carbon steel, aluminium sheet, iron plates, brass, steel, galvanized sheet and plates, other sheet metals and metal tubes.

1.Firstly,Advantage of xt laser welder.

1).Firstly,Laser welding gun weight is light,easy to move.
2).Secondly,Compact size , save floor space, easy to move.
3).Thirdly,IPG/Raycus/Maxphotonics laser source, good quality , 100000 hours life span.
4).And also,Environment-friendly , protect operator health.
5).And Fashion outlook .
6).And wobble welding function.

2.Secondly,Welding machine picture.

handheld fiber laser welder

3.Thirdly,Handheld welding gun.

handheld fiber laser welder

4.And also,Welding videos FYI.

https://youtu.be/appkDxaXXsA

https://youtu.be/30jjfMJCAM8

https://youtu.be/i-E_KmPJALU

https://youtu.be/W6IbPqn51hg

https://youtu.be/2Yy3vZt8y2Q

5.And also,Welding machine power.

1kw,1.5kw,2kw.

6.Next,Laser source.

Top and most popular brand is IPG/Raycus/Max.

IPG is Germany brand laser source,so the performance is the best.However,cost is also the most expensive.

Raycus and Max is top China brand,Raycus has bigger market share in the laser market.

Because Raycus found earlier than Max.

Advantage of Max source is its voltage.

1kw,IPG/Raycus/Max,support Single phase 220V.

1.5kw,IPG/Max support 220V,Raycus support 3 phases 380V.

2kw,IPG/Raycus/Max,support 3 phases 380V.

More questions just let us know.
Jill from XT LASER
E: xintian143@xtlaser.com
WhatsApp&Wechat&Mobile: +86 130 4603 3839
Skype: lasermachine01

Common questions of Handheld welding machine-Ivy

2020-05-06/in auto wire feeder laser welding machine /by Admin

Hi All,now Handheld welding machine gain more popular,here sharing with you some common questions as follow:

1.Can we adjust the welding speed?

yes, moving speed depend on operator’s hand.

2.Can we adjust the wire speed?

Yes, wire speed can be controlled on feeder.

3.Can we adjust the wattage?

Yes,we can control power output rate on touch screen board.

4.Can we put different diameter of welding wire?

Yes, usually 0.8mm dia is popular.

Spot dia ≥ wire dia ≥ gap width

5.Can we tack inside a 12MMx6MMx12MM U-shaped piece (see picture)?

Yes, but you need take away the wire feeder as its width is so small.

It is easy to do.

6.Can we grindnuzzle?

Yes, you can grind the nuzzle and make it suit your welding parts.

7.The device requires calibration before first use?

No need. we have calibration machine before delivery.
But you need adjust parameter like power rate, frequency etc according to your material thickness and welding performance.
It is easy and just need adjust 2~3 parameter.
After your people use few days and get suitable parameter for each thickness, it will be more easy.

8.Does the device need calibration during productive use?
As i said you just need change to suitable parameter when welding different thickness.

You can make a parameter sheet and what kind of parameter should use when weld different thickness.
In this case, even green hand can use it well.

9.Can we weld without shielding gas?
Yes, even without any gas it can work.
I show you video in last email, we didn’t use any auxiliary gas.

10.Is cooling the tip of the head necessary?
Water chiller have connect to laser head, you don’t need do any cooling way for any part.

Commom questions about fiber laser welder-Teresa

2020-04-22/in auto wire feeder laser welding machine, laser welding machine /by Admin

Commom questions about fiber laser welder

Nowadays handheld fiber laser welding machine is quite popular in laser market. It can weld stainless steel, mild steel, carbon steel, aluminium sheet, iron plates, brass, steel, galvanized sheet and plates, other sheet metals and metal tubes. Here we would like to introduce some common questions that most customers will ask.

1. Is the welding machine easy to operate?

Yes. The operating syetem can be set in English. And you just need to set some different parameters on the screen. There’s no problem to learn how to use it in few hours.

2. Does the machine need auxiliary gas?

Yes, Nitrogen (N2) or Argon both are OK. But for materials easy to be oxidized, Argon is better.

The gas can isolate the air from the welding plate to prevent reaction with the air. So the welding surface of the metal plate will be white and beautiful. The gas also can protect the lens from welding dust.

3.Does the machine have quick wear parts?
Yes, protective lens (8usd/piece).
With auto wire feeder, it takes about 7 days to replace the protective lens.
Without auto wire feeder, it takes 4-7 days to replace the protective lens.
Better environment, better operation, longer using time.

4.How to ensure the safety of handheld laser welder?

1). Machine system includes safety protection. And machine will work only when the clip and the welding head( gun) contact with metal at the same time, which can protect the operator’s safety.

2). High temperature resistant gloves
When you use the machine, please wear gloves for double safe.

3). Goggles
Machine come with Goggles for eye protection,we consider every details for customers.

For more information, please feel free to contact us.

Email: xintian105@xtlaser.com

Whatsapp/Mobile: +8615006829603

Skype: xtlaser Teresa

Advantages of wobble welding head on fiber laser welder-Teresa

2020-02-13/in auto wire feeder laser welding machine, Company News, laser welding machine /by Admin

Advantages of wobble welding head on fiber laser welder

XTLASER handheld fiber laser welding machine is equipped with a wobble welding head to fill the gap of hand held welding in the laser equipment industry.

What’s the advantages of wobble welding head?

Firstly, the process that the usual head can not complete, the wobble welding head only needs to use about 70% of the power. So the cost of the laser can be saved;

Secondly, wobble welding back and forth through the galvanometer motor. For material with large impurity, it can reduce bubble, fried point, splash, etc.

Thirdly, in the case of irregular gaps, the requirements for the fixture can be reduced.
The usual head welding gap is generally 0.2 mm. If over 0.2mm, light will go directly through it. There is no galvanometer motor in the welding head, so there is no swing. The welding effect is not good. And the welding process is limited.

With wobble head, the width of the gap that can be welded can reach 0.5mm.

If you want to know more information about fiber laser welding machine, please feel free to contact us.

Email: xintian105@xtlaser.com

Whatsapp/Mobile: +8615006829603

Skype:xtlaser Teresa

Common questions about handheld fiber laser welder-Teresa

2020-02-12/in auto wire feeder laser welding machine, Company News, laser welding machine /by Admin

Common questions about handheld fiber laser welder

XTLASER Handheld Fiber Laser Welding Machine is a new type high-power, high-end continuous welding tool. It adopts a high-quality fiber laser source to produce a fiber optic beam. After transmission processing, the light is focused on the workpiece to achieve continuous welding. It has the advantages of simple operation, beautiful beam, fast welding speed. Besides, it avoids the two thresholds of thermal strain and post-treatment. And it is environmentally friendly and pollution-free, greatly improving the joint strength and quality of welding.

Common questions about fiber laser welder

Firstly, is the welding machine easy to operate?
Yes. We can set the operating syetem in English. And you just need to set some different parameters on the screen. It is no problem to learn how to use it in few hours.

Secondly, does the machine need auxiliary gas?
Yes, Nitrogen (N2) or Argon both are OK. But for materials easy to be oxidized, Argon is better.

Thirdly, does the machine have quick wear parts?
Yes, protective lens. It usually takes 4-7 days to replace the protective lens. Better environment, better operation, longer using time.

For more informaion about fiber laser welding machine, please feel free to contact us.

Email: xintian105@xtlaser.com

Whatsapp/Mobile: +8615006829603

Skype: xtlaser Teresa

How to maintain handheld fiber laser welding machine-Teresa

2020-01-07/in auto wire feeder laser welding machine, Industry news, laser welding machine /by Admin

How to maintain handheld fiber laser welding machine

Nowadays, fiber laser welding machine is quite popular in welding industries. Because it has high welding precision and high speed. After long-term use, its welding efficiency may decrease. And we need maintain it regularly. So when we using handheld FIBER laser welding machine, how to maintain it? XTLASER will give you some suggestions.

Firstly, Check the optical path components of laser welding machine.

In order to ensure that the laser welding machine laser device is always in normal working condition. After continuous work or stop using for a period of time, before starting machine, check the components in the optical path such as the dielectric diaphragm and the lens protection glass. To ensure that all optical components are not contaminated. If there is any pollution, handle it in time. This can ensure that the optical components of laser welding machine will not broken under the strong laser irradiation.

Secondly, Check the conductivity of the inner circulating water.

The purity of cooling water is the key to ensure the laser output efficiency. It is important to check the conductivity of internal circulating water once a week to ensure its conductivity.

Thirdly, Check and adjust the laser cavity.

Operators can often check the laser output spot with black paper. Once find that the spot is uneven or the energy decreases, he should adjust laser cavity in time to ensure the laser beam quality. The adjustment of the laser must be carried out by specially trained personnel. Otherwise the laser deflection will cause other components on the optical path damage.

These are the maintenance methods of handheld fiber laser welder. It is important to maintain our machine regularly to ensure its welding efficiency. To learn more details about our laser welding machine, feel free to contact us.

Skype: xtlaser Teresa

WhatsApp: +8615006829603

Email: xintian105@xtlaser.com

XTLASER New Design Handheld Fiber Laser Welding Machine-Claudia Ma

2020-01-04/in auto wire feeder laser welding machine, Company News /by Admin

Laser welding :Handheld Fiber Laser Welding Machine.

Laser Welding Machine

If you are major in metal processing industry,whether stainless steel, carbon steel or aluminum,just read this blog.

We design new handhled laser welding machine to help with your business,let us learn it.

1.Machine picture showing.

Different from cutting machine,the welding mahcine is small size and easy to operate,don’t need our enigneer go to your factory to install and training.

We provide after-sales service department to teach you operating mahcine online,support vidoe call,you can learn it well in a few times.

2.Welding video for your reference.

When the gap is larger than 0.5mm,we need fill 0.8-1.0mm wire,we can provide auto wire feeding device.

It is convient to operate and save more times,manual cost.

In Dec,2019,we have sold more than 20 sets Raycus welding machine,most customers like auto feeding function.

3.Welding Capability for each metal.

No.	Material	Depth of fusion	Welding thickness
1	Stainless Steel	≤4mm	≤6mm
2	Mild steel/Iron	≤4mm	≤6mm
3	Galvanized sheet	≤4mm	≤5mm
4	Aluminum/brass	≤2mm	≤3mm

Hope you can have a basic learn for this new design fiber laser welding mahcine,many thanks!

Claudia Ma-XTLASER.

Email: xintian126@xtlaser.com.

Cell /whatsapp/Wechat: +86 17852254044

Handheld welding machine for 1-5mm metal-Ivy

2020-01-02/in auto wire feeder laser welding machine /by Admin

Handheld welding machine for 1-5mm metal

Recently,More and more customers asking for Handheld welding machine for 1-5mm metal,now in the market,1kw and 1.5kw gain more popular,here some details based on 1kw.

Price:

Quotation	FOB Qingdao $12500
Machine Name	1kw Handheld Laser Welding Machine with Wobble Head
Machine Model	XT-W1000
Wobble Head
Laser Source	1kw Raycus/IPG

Technical Parameters

Machine Name	Hanheld Laser Welding Machine
Laser Power	1KW
Electric Power	7.5kw
Cooling mode	Water Cooling
Laser pulse Frequency	1-20HZ
Pulse width	0.1-20ms
Adjusted spot range	0.1-3.0mm
Spot size	0.2-3.0mm
Minimum welding pool	0.1mm
Machine dimension	62.5109175cm
Water tank	Inbuilt model
Grand weight	250kgs
Optical Fiber	50um,10M
Continous Working Time	24 hours
Comllimation Length	F=50mm
Laser source	Raycus/IPG

Advantages of laser welding wobble head:
1. The process that the conventional head can not complete, the dithering head only needs to use about 70% of the power, so that the cost of the laser can be saved.
2. Wobble welding back and forth through the galvanometer motor, so that the bubbles with large impurities can reduce bubbles, frying, splashing, etc.
3. In the case of irregular gaps, the requirements for the fixture can be reduced. The conventional oscillating head welding gap is generally 0.2 mm, and light exceeding this width directly passes through. The width of the gap that can be welded by the oscillating head can reach 0.5mm. but the conventional welding head can only be welded to 0.2mm. There is no galvanometer motor in the welding head, so there is no swing. The welding effect is not good, the welding process is limited.

Wechat/whatsapp 0086 17864184107

xintian108@xtlaser.com