Příspěvky

Details of CO2 laser cutting and engraving machine.–Oriole

/in , , , , /by

Details of CO2 laser cutting and engraving machine.

Nowadays, more and more people majoring in wooden artware or other products making. With the technology developing so quickly, a lot of them choose CO2 laser cutting and engraving machine to finish their work.

In order to let you know more about CO2 laser cutting and engraving machine. Here share some details about with you.

What can the machine do?

CO2 Laser Engraving and Cutting Machine

CO2 Laser Engraving and Cutting Machine

CO2 laser cutting and engraving machine can cut and engrave wood, leather, pvc, acrylic, etc.

Is there any protection device for the machine?
Our machine has cover protection (when the front cover of the machine is opened, the laser will stop working), emergency stop switch (in an emergency, you can immediately press to cut off the power of the machine), cooling system protection (if the laser tube cooling system has a problem, the laser Will stop working), all doors on the machine can be locked with a key, which is more safe and secure

To amplify the power, can it be achieved by only using a high-power power supply or replacing a laser tube with a higher power?
No, it need to change the laser power supply and laser tube at the same time.

For example, a 60watt laser power supply can only support the work of a laser tube up to 60watts. If you only replace the 80watt laser power supply without replacing the corresponding laser tube, it will generate a certain current pressure on the 60w laser tube, which will affect the life of the laser tube. Make an impact. On the contrary, if you change to an 80watt laser tube without replacing the corresponding laser power supply, it may be impossible to drive the laser tube due to the low current. (In addition, if you replace a larger wattage laser power supply and laser tube, the chiller must be replaced with a larger model. It is also necessary to consider whether the laser tube box can fit a larger wattage laser tube.)

Any need please contact us at any time.

Oriole

Tel:13731273956

The application of CO2 laser marking machine Martin

/in /by

The application of CO2 laser marking machine Martin

The application of CO2 laser marking machine Martin

Hi there, the last blog, we introduce the application of our laser marking machine. This blog introduces the CO2 laser marking machine.

As we knew, the fiber laser marking machine could mark and engrave all metal, alloy, and some hard plastic. But if we want to mark on plastic, such as bamboo, wood, paper, ABS, PVC, acrylic, leather, rubber, leather, etc.

What should we do?

Expect a fiber laser marking machine, we could use the CO2 laser marking machine to do this work.

Some clients want to do craft need this machine. They usually want to mark on bamboo, wood, paper, ABS, etc. For example, we want to remember one moment. We could use CO2 laser marking machine to marking on wood. It is very interesting and ingenious. Make this moment more special.

Some Ads maker like this machine too. Usually, the purchase a CO2 laser machine to mark on some woods and acrylic, etc. Using this machine to mark a pleasant pattern. Make people impressed and easy to remember. It is make advertising’s result better.

Also, there is some clothes maker need this machine. As we know, the CO2 laser marking machine could mark on the leather, cloth, etc. So when they complete the shoes, if their clients want to mark their name, they could use this machine to do this. It can easily work. Also, some of their clients want to mark a special picture. It can easily achieve. For example, if some clients want to mark on their clothes. Let their clothes more meaningful.

The above application is popular.

 

The application of CO2 laser marking machine Martin

If you are interested in us. Please feel free to contact us:
Contact person: Martin Song
Email: xintia125@xtlaser.com
WhatsApp/ WeChat: +86 186 1267 4468

CO2 RF metal tube laser marking machine-Jill

/in , , /by

CO2 RF metal tube laser marking machine-Jill

CO2 RF metal tube laser marking machine

CO2 RF metal tube laser marking machine

>Applicable Industry.
Firstly,fiber is mainly for metal and CO2 is mainly for non-metal.

Therefore,this series of machine is suitable to advertising decoration, fabric, cloth, art gift, garment, leather, toy, computerized and clipping, packing and printing, paper product and other speediness processing industries.

And also nonmetal materials such as bamboo, plexiglass, acrylic, putamina of coconut, leather, wollens, rubber, paper.
>>Characteristics
Firstly,with the superior galvo system, the scanning speed can reach to most quickly 7000 mm/s, and the effect is better.
And also,with imported lens, the light spot is smaller, and the process effect is better.
So that you can choose manual or automatic worktable, put materials on and off when the machine

Marking sample

CO2 RF metal tube laser marking machineCO2 RF metal tube laser marking machine

CO2 RF metal tube laser marking machine

Marking videos:

Firstly,it is wood.

https://youtu.be/Yv1o8JD7klY

https://youtu.be/6vg5Brxnxfg

https://youtu.be/08jzMPui6y4

https://youtu.be/z4vzJpe6ISI

Secondly,it is leather.

https://youtu.be/igRETlyynlY

https://youtu.be/KjO8MV2HZXs

Thirdly,it is paper.

https://youtu.be/dd5y9PUaWS4

https://youtu.be/t5nHd_jSdnA

https://youtu.be/fMwZaafos0c

Fourthly,it is bamboo.

https://youtu.be/XgnCbYSF3Mc

https://youtu.be/l3SntM6DYR0

For glasses marking,it can also mark by uv,you can also check the below article:

https://www.xtlaser.cz/uv-laser-marking-machineglasses-bottle-plastic-marking-jill/

More questions just let us know.
Jill from XT LASER
E: xintian101@xtlaser.com
WhatsApp&Wechat&Mobile: +86 130 4603 3839
Skype: lasermachine01

Introduction of CO2 laser marking machine-Ivy

/in /by

Introduction of CO2 laser marking machine

The CO2 laser marking machine uses a laser beam to mark permanent surfaces on a variety of different materials.

The effect of marking is to expose deep materials through evaporation of surface materials, thereby engraving exquisite patterns, trademarks, dates, logos or characters.

At present, CO2 laser marking machines are mainly using in some occasions requiring more precise and higher precision.

Used in food, medicine, wine, electronic components, integrated circuits (IC), electrical appliances, mobile communications, building materials, PVC pipe and other industries, the main advantage of CO2 laser marking machine and inkjet printer is that there is no consumables and permanent

Applicable materials and industrial applications

The CO2 laser marking machine can engrave a variety of non-metallic materials.

Used in garment accessories, pharmaceutical packaging, architectural ceramics, beverage packaging, fabric cutting, rubber products, shell nameplates, craft gifts, electronic components, leather fabrics, bamboo and wood products, label paper and other industries.

Typical application cases, such as laser marking of packaging boxes, paper printing, and printing of metal detonator casings.

Manual

Check the water circuit and circuit before turning it on. The boot sequence is:
Firstly, turn on the incoming power and turn on the key switch. At this time, the machine exhaust and the refrigeration system are energizing, and the ammeter shows a value of about 7A;
Secondly, wait 5 to 10 seconds, press the trigger button on the external control panel, the current meter display value is zero, after 3 to 5 seconds, the xenon lamp is ignited, and the ammeter displays the value 7A. (Refer to the laser power supply operating instructions);
Thirdly, turn on the galvanometer power supply;
Fourth, turn on the computer and call up the required marking file;
Fifth, adjust the laser power to the working current (10 ~ 18A), you can start marking;

After the marking is finished, reverse the power of each component in the above order:

Firstly, adjust the laser power supply operating current to a minimum (about 7A);
Secondly, turn off the computer;
Thirdly, turn off the galvanometer power supply;
Fourth, press the stop button;
Fifth, turn off the key switch;
Sixth, disconnect the incoming power.

Wechat&Whatsapp:008617864184107

 

CO2 laser marking machine and fiber laser marking machine-Anne

/in , , , /by

CO2 laser marking machine and fiber laser marking machine

Classification of marking machines

Co2 machine according to different laser divide into imported metal tube laser marking machine and domestic glass tube laser marking machine

The laser wavelength of CO2 laser marking machine is 10.64um. CO2 laser, 10.64field mirror, 10.64 beam expander, so CO2 laser power supply, scanning vibroscope, control computer, laser control card compos to co2 laser marking machine. Laser control software, laser frame, laser circulating water system, circuit control system and other components.

The difference between CO2 laser marking machine and optical fiber laser marking machine There are:

1. Carbon dioxide laser marking machine mainly for non-metallic materials, such as plastic, glass and so on, but after a period of time, need to inflate (carbon dioxide gas).

metal and non-metallic materials make Optical fiber laser marking machines.

In simple terms,so they combine the functions of carbon dioxide laser marking machines and semiconductor laser marking machines,

and the speed is more than three times that of semiconductors. There is no need to change accessories for 100,000 hours. laser marking equipment with High-power, high-brightness, high-precision .

laser marking machine

2. The price of carbon dioxide laser marking machine is relatively low.

The price level of domestic products is about 2 to 40, 000 But one limitation of carbon dioxide laser marking machines is that they can only be marked on non-metallic items.

The basic price of the optical fiber laser marking machine is between 3 and 14 thousand.

power level of the fiber laser that you need depend on different price.

Now, so the optical fiber laser marking machine is the most popular in the laser marking machine market.

Because of its high power, high brightness, the price and semiconductor can not be much different,so many people in semiconductor laser marking machine and optical fiber laser marking machine, so more choice of optical fiber laser marking machine.Carbon dioxide co2 RF tube is very stable, maintenance-free, forward * frequency The service life of the tube is generally longer, in about 7 years, the author sees that most of the customers who use the new V30 feedback, its machine uses about 7 years laser does not need to inflate, the longest use of 9 years without inflation.

What about the service life of domestic RF tubes?

the author saw that many domestic RF tube manufacturers said that their quality assurance of RF tubes was one and a half years, and that there was also a lot of customer feedback.

The power of domestic carbon dioxide co2 RF tube will decrease obviously in more than 2 years.

The author conjectures that the non-inflatable operation time of domestic carbon dioxide co2 RF tube is 3-4 years.

But since the RF tube is inflatable, it can continue to be used. so It can be expected that, plus inflatable into the frequency tube 8-10 years of use is no problem, domestic RF tube plus inflation should be able to use 4-5 years.

Hope  this information is helpful for you.

If you have any questions of machine.welcome to contact us.

Sales Manager:Anne Zhang

Mob.whatsapp:+8615098735595

Skype:amyzhang1321

Email:xintian121@xtlaser.com

The CO2 laser marking machine+Karina

/in /by

The CO2 laser marking machine

The CO2 laser marking machine uses a laser beam to mark permanent surfaces on a variety of different materials.

The effect of marking is to expose deep materials through evaporation of surface materials, thereby engraving exquisite patterns, trademarks, dates, logos or characters.

At present, CO2 laser marking machines are mainly using in some occasions requiring more precise and higher precision.

Used in food, medicine, wine, electronic components, integrated circuits (IC), electrical appliances, mobile communications, building materials, PVC pipe and other industries, the main advantage of CO2 laser marking machine and inkjet printer is that there is no consumables and permanent

Applicable materials and industrial applications

The CO2 laser marking machine can engrave a variety of non-metallic materials.

Used in garment accessories, pharmaceutical packaging, architectural ceramics, beverage packaging, fabric cutting, rubber products, shell nameplates, craft gifts, electronic components, leather fabrics, bamboo and wood products, label paper and other industries.

Typical application cases, such as laser marking of packaging boxes, paper printing, and printing of metal detonator casings.

Manual

Check the water circuit and circuit before turning it on. The boot sequence is:
Firstly, turn on the incoming power and turn on the key switch. At this time, the machine exhaust and the refrigeration system are energizing, and the ammeter shows a value of about 7A;
Secondly, wait 5 to 10 seconds, press the trigger button on the external control panel, the current meter display value is zero, after 3 to 5 seconds, the xenon lamp is ignited, and the ammeter displays the value 7A. (Refer to the laser power supply operating instructions);
Thirdly, turn on the galvanometer power supply;
Fourth, turn on the computer and call up the required marking file;
Fifth, adjust the laser power to the working current (10 ~ 18A), you can start marking;

After the marking is finished, reverse the power of each component in the above order:

Firstly, adjust the laser power supply operating current to a minimum (about 7A);
Secondly, turn off the computer;
Thirdly, turn off the galvanometer power supply;
Fourth, press the stop button;
Fifth, turn off the key switch;
Sixth, disconnect the incoming power.

Contact:Karina

Wechat&Whatsapp:008618206584205

Email:xintian103@xtlaser.com

Daily Maintenance Of fiber Laser Marking Machine(I)–Anne

/in , /by

Daily Maintenance Of fiber Laser Marking Machine

Fiber Laser marking machines are divided according to lasers, so we need to select different laser marking machines according to the working conditions, marking materials and format. As the most advanced laser marking equipment in the world, the fiber laser marking machine has a wide application range and is recognized as a new generation of solid laser replacement. It has good beam quality, fast marking speed, small size and convenient use. And the working life is long, and it has been favored in the marking industry. To achieve the normal use of fiber laser marking machine and long life, daily cleaning, maintenance and maintenance is essential.

XT Laser has accumulated a lot of experience over the years and hopes to bring great convenience to users:

1. In fact, it is relatively easy to maintain fo Fiber laser marking engraving machine, It is necessary to clean its fan, especially after long-term use. The laser marking equipment is clean inside and outside, and there is no oil on each sliding surface and screw. All parts are not leaking or leaking. Clean the filter regularly and wipe the lens. The mechanical engineers of the chips, debris and dirt around the laser marking equipment should be cleaned; the tools, accessories and workpieces (products) should be placed neatly, and the pipelines and lines should be organized;

2. Regularly check whether the screws of the instrument are fixed firmly. For the lens, it should be cleaned frequently, or it can be cleaned every day. However, when wiping the lens, it must be wiped with a special wiping cloth, which can not damage the lens.

3, in the process of use should be strictly in accordance with the operating procedures to avoid damage to the fiber laser marking machine (XT LASER will provide user manual and video for user’s learning).

4. The appearance of the laser marking equipment is clean.

Before and after each use, the necessary wiping, to ensure that the equipment is dust-free, clean is the key, and the equipment environment is also clean.

5, laser light path system maintenance, usually the internal light path of the machine is closed design, no need to clean. But if there is a need for cleaning, it is best to find a professional. When wiping the lens, gently wipe it with lens paper with a little alcohol to avoid damage to the optics.

6, air cooling system maintenance. Air-fiber laser marking machines use air-cooled cooling, so air-cooled equipment is particularly important. Check the fan regularly and repair or replace it in case of any abnormal response.

7. If there is any fault in the fiber laser marking machine, the power should be cut off immediately.

8. If the surface of the focusing mirror is contaminated, the focusing mirror should be removed to clean the lower surface.

For more tips,we will share to you in next article.

Sales Manager:Anne Zhang

Mob.whatsapp:+8615098735595

Skype:amyzhang1321

Email:xintian121@xtlaser.com

Advantages and operations of EZCAD software–Winnie

/in , , /by

Advantages and operations of EZCAD software

As we all know, EZCAD software is the software of laser marking machine, so it decide the machine operat process.

Ezcad2 is a professional marking software launched by Golden Orange Software Co., Ltd.,  The software is perfect to support TrueType fonts, single-line fonts (JSF), Array font (DMF), etc. And has flexible text processing, powerful compatibility and image processing functions to meet the needs of different users.

Languages of EZCAD software:

The EZCAD 2.14.9 international version of the software has been upgraded on the original software. The software fully supports UNICODE, so it can support the language of all countries basically.
EZCAD2.14.9 international version software can run on MICROSOFT WINDOWS XP, VISTA, WIN7 and WIN10 operating systems. EZCAD2.14.9 international version software installation is very simple, users only need to copy the EZCAD2.14.9 international version directory on the installation CD directly to the hard disk, after that remove the read-only properties of all files and folders. You can run the EZCAD2.14.9 International Edition program by double-clicking the EZCAD2EXE file in the directory.

Advantage of EZCAD software:

Freely design the graphic pattern.

Support for TrueType fonts, single line fonts (JSF), dot matrix fonts (DMF), 1D barcodes and 2D barcodes.

Flexible variable text processing. it could changing text in real time during processing, even could read / write text files and Excel files directly.

Powerful node editing and graphical editing for curve welding, cropping and intersection calculations.

Supports up to 256 pens (layers) so could set different processing parameters for different objects.

Compatible with common image formats (bmp, jpg, gif, tga, png, tif, etc.).

Compatible with commonly used vector graphics (ai, dxf, dst, plt, etc.).

Commonly used image processing functions (grayscale conversion, black and white map conversion, dot processing, etc.), so can perform 256-level grayscale image processing.

Powerful padding and support for ring fills.

A variety of control objects, so users can freely control the system to interact with external devices.

Open multi-language support makes it easy to support languages around the world.

The difference between fiber and CO2 laser marking machine-Teresa

/in , , /by

The difference between fiber and CO2 laser marking machine

First, this text mainly tell you the difference between fiber and Co2 laser marking machine. The difference between

the fiber and CO2 laser marking machine,  mainly exists in the wavelength and laser source. Most clients will ask this question.

The wavelength

Many clients, especially those new-challenger of this field, will always wonder the difference of the fiber and CO2 laser marking machine .  Actually, the biggest difference between fiber laser and CO2 laser marking machine is the wavelength. The fiber laser marking machine’s wavelength is 1064 nm. But the CO2 laser marking machine’s wavelength is 10.64 um.

This is why fiber laser marking machine could mark onto all metals and some plastics. But CO2 laser marking machine could

only work with non-metals.

The laser source

There is also another between the fiber and CO2 laser marking machine. The fiber laser marking machine use Raycus as its laser sourse. The CO2 laser machine use the Synrad as its laser source.

But all in all, these machines has the following after sale  service.

After sales Service

1. our service is available to each customer. And if any technical questions or problems, our engineers will help you .and give you solutions on the phone. or by face-to-face communication online.

2.Two-year warranty is provided.

3.Also the Professional staff for installation and training if needed.

4.And the spare parts are supplying on time. or doing some inventory if promising certain sales volume.

5.Faster delivery, we will support our sole agent to do the stock if good sales. then more convenient and helpful.

6.If the sales are good, we will arrange some famous exhibition fairs in the local or surroundings. and give our full support to our agents at the fair. We will provide our sample machines, catalog, DVD, manuals, etc. All native customers belong to our local agent. which is our basic rule. And we promise the final delivery is the same as displayed

If you want to more details, feel free to contact us.

Email: xintian105@xtlaser.com.

Whatsapp/Wechat/Mobile: +8615006829603

Skype: xtlaser Teresa

Can a fiber laser marking machine engrave wood?-Jill

/in , , /by

Can a  laser marking machine engrave wood?

laser marking machine engrave wood.If you’re looking for a powerful technology.Which we can use it to create clean.fast. high-contrast permanent marks for identification and trace ability. Fiber laser engraving machines are the way to go. Their advantage is high peak power and superior beam quality. This make them ideal solutions for marking and engraving on a wide variety of materials. Their versatility and other benefits are why we use fiber lasers  across industries. From automotive and aerospace to electronics and medical device manufacturing.

But can a  laser marking machine engrave wood?

Like many of our customers, you may want to expand the use of your fiber laser.And “get your money’s worth” by using it to engrave wood. Or for your wood product.you’re looking for an industrial engraving solution.  Either way, you want to find the best machine for the job at hand.

However, don’t (I repeat, don’t) use a fiber laser to mark wood. It can pose a serious fire hazard.

There are many other ways to safely use lasers to engrave – or even cut or weld – materials. But xt laser does not recommend.It is not safe to use a fiber laser for wood applications.

Reasons not to use a fiber laser to engrave wood

1.Fire=fiber laser marking machine engrave wood

Using a fiber laser on wood is essentially like starting a campfire.

The fiber laser  wavelength is 1064nm. Laser transmits partially through organic structures .(like wood) .It needs shorter wavelength. This is why we use 1064nm for medical procedures .Such as  laser eye surgery.where the laser beam travels through skin or eye tissues to do its work non-invasively at a deeper level.

Unlike the human eye. when the beam travels into wood,we can not control its absorption. This is because of the variances in the wood material. Heat builds up, and eventually the wood will ignite. This creates an extremely dangerous situation. The fire will spread quickly with the wood acting as fuel for the intense heat.

2.Fiber lasers create poor marks on wood.

The goal of any engraving project is to create a mark that is readable, either by human or machine. Uncontrolled absorption, however, results in an uncontrolled mark on wood. This looks uneven, with some places charred and others barely identifiable.

The bottom line: Fiber lasers + Wood = Dangerous conditions and Poor marks.

When they’re used correctly, fiber lasers can be highly effective and profitable machines, and there are plenty of fiber laser videos that showcase the abundant capabilities of this versatile technology.

 

So,how do u use a laser marking machine engrave wood?

There is another type of industrial laser engraving machine that can be a valuable tool to mark or engrave your wood products.

A CO2 laser will successfully mark wood without the safety risk of starting a fire. Its 10600nm wavelength is 10x larger and is easily absorbed by organic materials, reacting with wood like a true cutting tool.

The results are clean and controlled marks, free from charring and campfires. CO2 lasers are compact and cost-effective, making them popular solutions for companies upgrading from ink-jet or labeling part identification methods. With the capability to produce high-quality marks at high speeds, these lasers often help operations save costs and improve cycle times.

Many of our customers have used the CO2 to successfully add branding marks or trace ability information to their wooden products, including gun stocks, floor planks, pallets, barrels, and furniture.

More questions just let us know.
Jill from XT LASER
E: xintian101@xtlaser.com
WhatsApp&Wechat&Mobile: +86 130 4603 3839
Skype: lasermachine01