Příspěvky

High Power Laser Cutting Machine from XTLASER-Eliza

/in /by

High Power Laser Cutting Machine from XTLASER

High power laser cutting machine. With the development of laser technology.  High-power laser cutting machines can use air cutting when cutting carbon steel materials of more than 10mm. The cutting effect and speed are much better than those with low and medium power limit power cutting. Not only has the gas cost in the process reduced, and the speed is also several times higher than before. It is becoming more and more popular among metal processing industry.

Fiber laser cutter

Fiber laser cutter

 

The super high-power fiber laser cutting machine technology has obvious advantages when cutting metal materials of different thicknesses. How to correctly use the super-power fiber laser cutting machine to achieve the ideal cutting effect requires mastering its processing technical parameters and operating procedures. Especially in the cutting process of metal laser cutting machine, you must choose the appropriate cutting speed, otherwise it may cause several bad cutting results. The main manifestations are as follows:

What is the effect of the cutting speed of the high-power fiber cutter?

1. When the laser cutting speed is too fast, it will cause the following undesirable results:

① The phenomenon of inability to cut and random sparks;

②The cutting surface has oblique stripes, and melting stains are generated in the lower half;

③The whole section is thicker, and there is no melting stain;

2. When the laser cutting speed is too slow, it will cause:

①The cutting surface is rough, causing over-melting.

②The slit becomes wider and melts at the sharp corners.

③Affect the efficiency of cutting.

Therefore, in order to make the ultra-high-power fiber laser cutting machine better perform its cutting function, you can judge whether the feed speed is appropriate from the cutting spark of the laser equipment:

1. If the sparks spread from top to bottom, it indicates that the cutting speed is appropriate;

2. If the spark tilts backward, it indicates that the feed speed is too fast;

3. If the sparks appear to be non-spread and less, and condense together, it indicates that the speed is too slow.

So, with a good and steady laser cutting machine, and on time online afterserivce is also important to ensure the use of laser cutting machine.

 

Any questions, just feel free to contact

Eliza Liu

Whatsapp: 008613173025103

Email: lasermachine01@xtlaser.com

Operating cost of fiber laser cutter–Oriole

/in , , /by

Operating cost of fiber laser cutter

Fiber laser cutter

              Fiber laser cutter

For many small companies, it would be a relatively large investment if they use multiple or one laser cutting machine. Many factories can indeed appreciate the advantages of metal fiber laser cutting machines, but there are also many people who think that the cost of laser cutting is still relatively large. When it comes to laser cutting, it is already a familiar term in the processing industry, so many people think The metal laser cutting machine is suitable for large enterprises in terms of cost. Let’s take a look at how high the cost of the metal laser cutting machine is. Is it what we imagine?

The metal laser cutting machine is currently the latest type of laser cutting equipment. The laser cutting machine has higher cutting speed, better cutting quality and lower use cost. The metal laser cutting machine has high power from 1000w to 20000w. But the metal laser cutting machine has great advantages in thin sheet metal cutting. The cutting efficiency is far better than other laser cutting equipment on the market, which improves the stability of the system and reduces the equipment’s cost. The amount of maintenance, therefore, greatly reduces the maintenance cost of the equipment. There are some important reasons to control its cost.

Let’s take a look at how to control the cost of laser cutting machine operation. The cost of metal laser cutting machine in cutting is also very low, accounting for only about 1/8 of the same kind of CO2 laser cutting machine. The hourly use cost of metal laser cutting machine is about 30-40 yuan, while CO2 laser cutting The machine is about 200-240 yuan per hour. At the same time, because the cutting speed of the optical fiber laser cutting machine is very fast, it is nearly 300 times higher than that of the wire cutting. Therefore, the metal laser cutting machine creates a very low cost. A higher value. Nearly 80% of the cost of using laser cutting machines comes from the consumption of gas.

 

Any interests welcome to contact us for more information.

Oriole

Whatsapp/Wechat:008613731273956

How to maintain the cutting machine?–Oriole

/in , , , , /by

How to maintain the cutting machine?

Here are some details about the maintenance of  the cutting machine after using it.

  • Above all,clean.

Firstly,we need to clean the attached dust and cut slag on the surface of the equipment.

A fiber laser cutting machine.

A fiber  laser cutting.

Secondly,clean up the water in the A/C storage tank.

Thirdly,cleaning waste scraps and debris in waste trailers.

More over,clean the dust on the A/C dust cover net and the water cooler dust cover net.

Fifthly,clean the water tank of the water cooler.

Last but not least,clean the surface of the cutting head and focus on cleaning the cooling water pipe joint, auxiliary gas joint, protective lens window, QBH/QCS joint and other parts.

  • What’s more,check.

Firstly,check the joints of the capacitor signal module (at the cutting head) to confirm that the fastening is intact and there is no looseness.

Secondly,equipment homing(including X, Y and Z axes).

More over,check the lubricating oil level in the lubricating oil pump. If it is not enough, fill it in time.

Fourthly,check the lubrication condition of each shaft slide rail, rack, gear and z-axis screw; and manually add lubricating oil on the upper end surface and the two end surfaces of the guide rail, and the main mechanical linkage end face of the rack, gear and lead screw is evenly distributed. Apply lithium grease. (If there is rust, be sure to remove the rust first.)

Fifthly,check the water pipes of the cooling water pipe to confirm that there is no extrusion, bending, grinding, scratching and water leakage; check the water pipe joints (push-in connectors and ordinary threaded joints) to confirm that the connection is normal and there is no water leakage.

Sixthly,check if the cooling water pressure gauge value is normal.

What’s more,replace the water cooler to circulate cooling water.

At last,check the wiring harness and cable everywhere, and confirm that there are no extrusion, bending, grinding, and scratching. There is no open welding or short circuit or hidden trouble in the welding of the break point and the plug joint.

 

That is some of the maintenance of  the cutting machine after using it .

 

Mob/Whatsapp:+8613731273956

WeChat:xtlaseroriole

Email:xintian161@xtlaser.com

Skype:xintian161@xtlaser.com

web:www.xtlaser.com

High quality fiber laser cutting machine-Claudia

/in /by

High quality fiber laser cutting machine

More and more customers would like to ask for a low price fiber laser cutting machine with high quality.

Th fiber laser cutter could not only save the electronic, but also protect the environment.

Besides, it could save some maintenance cost.

For different thickness material with different power, we equip with the different fiber laser cutter.

For this big equipment, the customer may not concern more about the machine price.

What they notice is the machine quality and the warranty.

The supplier must pay attention to the machine using and the cutting outcome.

Trying their best to provide the best fiber laser cutting machine to the customers.

In recent days, we met with an Indian customer who ask for the 12mm carbon steel cutting.

For the carbon steel material, it would be easier to cut.

We usually use the oxygen as auxiliary gas to cut it, cause the oxygen could help burn the material.

And for the max 12mm thickness, the 1500w fiber laser cutting machine is good for cutting and assure the cutting outcome.

fiber laser cutting machine

To assure the cutting outcome, there are some spare parts in the fiber laser cutter, which is important.

For example, the water chiller.

It is plays a big role in the fiber laser cutter, which is important for cooling the laser source and cutting head.

We equip with the Tongfei brand water chiller, which specialize in the fiber laser cutting system.

Besides, the laser source is also important.

Raycus and IPG are both high quality laser source in this industry.

Some supplier may choose the Max laser source which is unstable at all.

Laser source is the most important part of the fiber laser cutter.

So the customers must choose the most suitable laser source in the whole machine.

If u want to learn more about the fiber laser cutting system, pls contact with me here:

Contact：Claudia

Email: xintian126@xtlaser.com

mobile/whatsup/WECHAT:+8617852254044

Carbon steel fiber lazer cutter 3000w power – Jill

/in , , /by

Carbon steel fiber lazer cutter 3000w power

Carbon steel fiber lazer cutter 3000w power.

Generally, will burn the material. Possible reasons as below.

(1) The laser focus position is offset, and the focus position test is performed, and the offset is adjusted according to the offset of the laser focus.

(2) The output power of the laser is not enough. It is necessary to check whether the work of the laser generator is normal. If it is normal, observe whether the output value of the laser control button is correct, if it is not adjusted properly.

(3) The cutting line speed is too slow, and it is necessary to increase the line speed during operation control.

(4) The cutting gas is not pure enough to provide high quality cutting working gas

(5) The instability of the machine tool running time is too long. At this time, it needs to be shut down and restarted.

Laser not completely cut

The reason why the laser is not completely cut.

(1) The selection of the laser nozzle does not match the thickness of the processing plate, and the nozzle or processing plate is replaced.

(2) The laser cutting line speed is too fast, and the operation control is required to reduce the line speed.

Abnormal sparks when cutting low carbon steel.

When the low carbon steel is cut normally, the fire bouquet is long, flat, and has fewer splits. The occurrence of abnormal sparks will affect the smoothness and quality of the cut section of the work piece.

In this case, if other parameters are normal, the following should be considered.

Firstly,The laser head nozzle has serious loss, and the nozzle should be replaced in time.

Secondly, In the case of no new nozzle replacement, the working gas pressure should be increased.

Thirdly, If the thread at the joint between the nozzle and the laser head is loose, the cutting should be suspended immediately, check the connection state of the laser head, and re-thread the thread.

Finally,if you want to know some details,contact us.

And also,if for more questions just let us know.
Jill from XT LASER
E: xintian143@xtlaser.com
WhatsApp&Wechat&Mobile: +86 130 4603 3839
Skype: lasermachine01

How to protect eyes when using laser cutting machine-Phoebe

/in /by

How to protect eyes when using laser cutting machine

The laser cutting machine is professional equipment for metal plate cutting. As you know, laser have different safety levels, the laser-produced from metal laser cutting machine may do harm to our eyes, so when we use this machine, we should take some measures to protect eyes.

fiber laser cutting

The typical protective device for the machine is laser protective glasses, according to its protection principle, it can be divided into reflection type, absorption type, diffraction type and composite type. This is the safer and more convenient protection device of the laser machine.

Except wear protective glasses to protect eyes, there are also some tips to protect eyes.

(1). Paint the walls of the workplace darkly to reduce radiation;

(2). Install protective screens or drapes to minimize laser damage to the eyes. SENFENG SF3015H laser metal cutting machine has full protection to reduce laser radiation, many customers would like to buy this machine to do their metal processing business.

(3). Warning: in the work area, the operator does not look directly at the arc or flame while cutting.

These are some measures to protect eyes when using this machine. If you want to get more using tips about our machine, do not hesitate to contact us.

WhatsApp: 0086-15014021522

E-mail: xintian120@xtlaser.com

Fiber laser marking machine for metal tags-Bonnie

/in , /by

Fiber laser marking machine for metal tags and plates

Tags or plates may appear not very significant in the overall process of product manufacturing. But they sometimes play crucial role in the product lifecycle. Why are plates important? Where to use them? Why is fiber laser marking machine the perfect match? The article will provide the answers to these questions. And show engraving nameplates are essential for various industries.

Why Are Tags Used?


In general, tags and plates (or nameplates) mean to keep the information about the product they are attached to. Batch codes, manufacturer’s ID, date identification, part numbering, lot or shift codes and other data to identify and trace the product is safe with tags.

Tags are quite popular for product, part and equipment labeling. Especially in the situations, when inscribing on the product directly is impossible on technological, safety or other reasons. Nameplates are also widely used in other aspects. Assets and property inventory, pets and cattle identification, VIN numbering, keeping medical alert information, etc.

Fiber laser marking machine for metal

The product has to be traced and identified during the entire lifetime. Therefore tags are usually metal material. But using this wear resistant and durable material is not enough. Because it is only the holder of the necessary information. The information put on the tag has to be indelible as well. If your demands to the number and quality of the tags are higher, the best solution is a fiber laser marking machine.

7 Benefits of fiber laser marking machine


● Works fast
● Smoothly integrates into the manufacturing process
● Easy to operate
● Superior adaptability and wide customization options
● Compact and easy to store
● The technology requires no consumables
● Excellent quality means high precision at once, no defects

As a result, a manufacturer can mark any necessary quantity of nameplates quickly without sacrificing the quality. The information on the tag will be easily readable both by human eye and by the industrial scanner. And resistible to any kind of exposure.Thus, fiber laser marking machine is the answer to the requests of those customers.

Conclusion

Metal plates, tags need quality and permanent engraving. With fiber laser marking machine metal, tags will achieve good quality. And accurate marks serving your product for as long as you need and even longer. With XTLASER solutions, you will get the best result quickly and easily.

Contact us to get fast and effective nameplate marking machines with our solutions.

Pipes Fiber Laser Cutting Machine in Tube Cutting-Bonnie

/in /by

Pipes Fiber Laser Cutting Machine in Tube Cutting

With the application of laser cutting machine more and more extensive, single plate cutting has been unable to meet the processing requirements, pipes fiber laser cutting machine comes into the public eye gradually.

Under this circumstance,  xtlaser developed automatic metal tube laser cutting machine independently to meet industrial cutting needs. Compared with the general pipe cutting machine, it has the following main advantages:

Firstly. Automatic loading and unloading.

Through the numerical control system to realize the loading and unloading, automatic collection of finished products and materials,saving labor costs and improving cutting efficiency.

Secondly. Be suitable for different shapes of pipe.

It can cut rectangular tube, round tube, square tube, p-shaped pipe, and other rectangular pipe.

Thirdly. Floating Support

Floating support is that it does not limit the positioning freedom, and ensure the reliability of the original position. Usually it is an auxiliary means. In tube laser cutting machine, it ensure the pipe suitable and keep it in the same straight line.

Above all, Professional pipe laser cutting machine not only can replace mechanical drilling, milling, sawing, stamping and burring, avoid processing with multiple devices, but also  it can achieve the complex pipe structure cutting, chamfering and other possible size and shape characteristics processing.

So far, we have sold the machines in demostic and aboard.  After many improvements, the various processes are very mature and the performance is stable. When using, if you have any problems, our technical engineers will answer you for the first time.

If you are interested in it, please feel free to contact us!

 

How To Use Fiber Laser Cutting Machine-Anne

/in , /by

How To Use Fiber Laser Cutting Machine

Lately, fiber laser cutting became more and more popular in metal cutting industrials. a large amount of factories have their own machines for metal cutting.

But, as we know the laser cutting working process is a new craft, some customers are facing some problems for operate the machine.

Actually, if you do know the principle of laser and machine. The problems are easy to solve. Therefore, I will give you some useful tips. It might help you to better understanding how to use the fiber laser cutting machine.

 

Carbon Steel.

 

Carbon Steel is not a highreflection material. It is not like aluminum or brass. This material is the most suitable material for fiber laser cutting. For the cutting effect, any machines you can find in the market are able to cut carbon steel with a perfect effect.  The application of carbon steel is more and more extensive. The maximum thickness of carbon steel plate can be cut by modern laser cutting machine up to 20MM. Using twinjet nozzle, The cutting seam of carbon steel can be controlled in the range of satisfactory width by using oxidation melting cutting mechanism, and the cutting seam of thin plate can be narrowed to about 0.1mm.

 

Stainless Steel.

 

Laser cutting of stainless steel, using the energy released by a laser beam to the surface of a steel plate to melt and vaporize the stainless steel.

Laser cutting of stainless steel is a fast and effective method for manufacturing of stainless steel sheet as main component. Cutting speed, laser power, air pressure and so on are the most important technological parameters affecting the cutting quality of stainless steel. Compared with low carbon steel, stainless steel cutting requires higher laser power and higher oxygen pressure.

But the stainless steel cutting achieves satisfactory cutting effect, it is difficult to obtain the completely nonstick slag cutting seam.

In general, high pressure nitrogen and laser beam coaxial injection are used to blow away molten metal so that no oxide is formed on the cutting surface.

This is a good method, but more expensive than conventional oxygen cutting. One alternative to pure nitrogen is to use filtered compressed air in the workshop, which consists of 78% nitrogen. Using air to cut the metal sheet also need add three main parts. air tank, air comperssor, and air filter.

If you have any questions about machine,welcome to contact us.

Sales Manager:Anne Zhang

Mob.whatsapp:+8615098735595

Skype:amyzhang1321

Email:xintian121@xtlaser.com

 

3 Factors Will Affect The Circular Hole Cutting Of Fiber Laser Cutting Machine -Anne

/in /by

3 Factors Will Affect The Circular Hole Cutting Of Fiber Laser Cutting Machine

In metal processing industries, it requires perforation for many metal processing jobs. There are many equipment can punch hole in the market, fiber laser cutting machine is one of them. Compared with other cutting equipment, it is more precise and faster. When use fiber laser cutter to cut circular hole, there are many matters that users should be paid attention to.

1.Choose suitable gas pressure

Too excessive or too small both can influence cutting effect. When the gas pressure is too small, the cutting edge will be rough. The hole will popping when the gas pressure is too excessive. The gas pressure is better to above 1.6Mpa when cut stainless steel by nitrogen. If use oxygen to cut stainless steel and carbon steel, the thicker the steel, the lower the pressure.

2.Servo motor parameters

Servo motor parameters are related to the circular movement.
If the parameters are not correct, the mismatch of the X and Y axes movement will cause the ellipse or irregular shape when cutting circular holes.

3.The hole size

It is better to cut 1:1 hole. The larger the aperture, the better the cutting result.
These are the important matters when cutting circular hole with fiber laser cutter. If you want to know more technical details about our machine, free to contact us.

Sales Manager:Anne Zhang

Mob.whatsapp:+8615098735595

Skype:amyzhang1321

Email:xintian121@xtlaser.com